Table of Contents

Class BreakageProbability

Namespace
Hi.Physics
Assembly
HiMech.dll

The probability that a cutter beam breaks under a bending stress: the Weibull form on the stress over the beam material's bending strength, P = 1 − 0.5(σ ÷ σb)m, with the material's bending strength σb as the median (half the test bars of a brittle material break at the catalogue's transverse rupture strength, so P is 1/2 there) and the Weibull modulus m as the shape of the scatter of that strength from bar to bar. A brittle strength is set by the worst flaw of the piece, so the probability is that of one stress and not a count over steps: a cutter that held a stress holds the same stress again; fatigue is not modelled. What a step's breakage probability (MachiningStep.BreakageProbability_percent) reads, in percent, off its stored stress ratio and the beam material of the moment, and a tool's over the whole run off its largest stress ratio so far (Hi.MachiningProcs.ToolStressHighWater). The owner's ask of 2026-11-03: the ratio's 100 % is where breakage becomes possible, not certain, and a probability says how possible.

public static class BreakageProbability
Inheritance
BreakageProbability
Inherited Members

Remarks

Two assumptions stand in for data a material file may not give, each named at its member: the modulus (DefaultWeibullModulus) and the bending strength of a material that gives a tensile strength alone (BendingStrengthOf_MPa(IStructureMaterial)). A ductile beam material – one that gives a yield strength, an insert-end cutter's steel body – is rated by the same form, its stress the ratio times its yield strength and its bending strength the stand-in from its tensile strength: the brittle form applied to a steel, an assumption to read as such (the design of 2026-11-03; a measured bending strength in its file replaces the stand-in). The modulus is never derived from a file's tensile and fracture strengths: the two are seldom one batch's measurements of one test (the shipped binder grades' listings imply 4.2 to 4.9, no carbide's, and the binderless WC's 13: the pairs are not one test's), and only a pair measured together (1.79 at 10 % Co, 1977) implies the 9 a carbide has. The spindle torque and power ratios do not enter the probability. The spindle speed under load is simulated (MachiningStep.SpindleSpeedUnderLoad_rpm, MachiningStep.SpindleSpeedDeviation_percent), but it is not fed back into the force: a slower spindle raises the feed per tooth and with it the force and the stress ratio, while the stress ratio and this probability are the values at the commanded speed.

Fields

DefaultWeibullModulus

The Weibull modulus taken for a material that gives none (WeibullModulus NaN or not above 0): 10, the middle of the 8 to 20 the carbide literature reports for small test bars. An assumption.

public const double DefaultWeibullModulus = 10

Field Value

double

Methods

BendingOverTensile(double)

The bending strength over the tensile strength of a brittle material whose strength scatters with Weibull modulus weibullModulus: [2(m + 1)²]1/m, the volume effect of a bar bent in three points against one pulled whole – the bent bar stresses a small volume at its outer fibre and so meets a weaker worst flaw less often. 1.73 at m = 10. An assumption (a ductile steel does not scatter so, and a measured pair of a carbide runs 1.4 to 1.8), used for a material that gives no fracture strength.

public static double BendingOverTensile(double weibullModulus)

Parameters

weibullModulus double

The Weibull modulus; NaN or not above 0 answers NaN.

Returns

double

BendingStrengthOf_MPa(IStructureMaterial)

The bending strength the probability rates a stress against, in MPa: the material's FractureStrength_MPa where it gives one above 0 (a carbide's transverse rupture strength, the shipped carbide files' catalogue median; the shipped high-speed steels' bending rupture strength from published data); else its TensileStrength_MPa times BendingOverTensile(double) at WeibullModulusOf(IStructureMaterial) – the assumption for a material that lists a tensile strength alone, as the shipped ceramic and CBN do and as a ductile insert body does (the volume-effect stand-in is a brittle strength's: read as an assumption there); else NaN (no strength, no probability). NaN for null.

public static double BendingStrengthOf_MPa(IStructureMaterial material)

Parameters

material IStructureMaterial

The beam material; may be null.

Returns

double

Of(double, double, double)

The breakage probability, 0 to 1, of a bending stress against a bending strength scattered with a Weibull modulus: 1 − 0.5(σ ÷ σb)m, which is exactly 1/2 at the strength (its median), 0 at no stress, and climbs as the m-th power below the strength – at m = 10 a stress of 0.408 of the strength (the shipped WC-Co6-800nm's stress limit 1550 over its 3800) gives 8.84 × 10−5, about one in eleven thousand. Where the exponent is small the value is the series of 1 − e−t (t = ln 2 · (σ ÷ σb)m), so a light cut keeps its digits instead of rounding to 0.

public static double Of(double stress_MPa, double bendingStrength_MPa, double weibullModulus)

Parameters

stress_MPa double

The bending stress at the section; NaN answers NaN; 0 or below answers 0 where the strength and the modulus are above 0.

bendingStrength_MPa double

The median bending strength; NaN or not above 0 answers NaN whatever the stress.

weibullModulus double

The Weibull modulus; NaN or not above 0 answers NaN whatever the stress.

Returns

double

OfStressRatio(double, IStructureMaterial)

The breakage probability, 0 to 1, of a step's stored stress ratio on its beam material: the ratio times the material's stress limit (StressLimit_MPa) is the stress at the critical section, rated by Of(double, double, double) against BendingStrengthOf_MPa(IStructureMaterial) at WeibullModulusOf(IStructureMaterial). The stored ratio is the play's: a stress limit edited after the play moves the product where the material gives a fracture strength (where the bending strength is derived from the same tensile strength the product does not move with it), and the ratio in neither case, until a step-physics recompute (the ratio's inputs are fingerprinted); a bending strength or a modulus edited after it reaches the read at once (neither is an input of a stored value). The product ratio × stress limit may miss the bending strength by an ulp, so 1/2 at the strength is exact through Of(double, double, double) alone.

public static double OfStressRatio(double stressRatio, IStructureMaterial material)

Parameters

stressRatio double

The step's stress ratio; NaN answers NaN; 0 answers 0 where the material gives a stress limit and a bending strength, else NaN.

material IStructureMaterial

The beam material of the moment; null answers NaN.

Returns

double

WeibullModulusOf(IStructureMaterial)

The Weibull modulus the probability takes for material: the material's where it gives one above 0, else DefaultWeibullModulus; the default for null.

public static double WeibullModulusOf(IStructureMaterial material)

Parameters

material IStructureMaterial

The beam material; may be null.

Returns

double